|
|
 |
|
|
|
- GENERAL
Recording Format : IEC DAT Standard Part1
IEC DAT Standard Part5 (w/model 8335)
Number of Channel : Audio x2
Audio x2, Timecode x1 (w/model 8335)
Recording Time : 120 minutes (T-120 tape)
Head Configuration : Rotating 2 heads
Error Correction : Double Encoded Reed Solomon Code
Sampling Frequency : 48kHz, 44.1kHz
Quantization : 16bit linear
A/D Converter : 18bit Delta-Sigma 64 times over sampling
D/A Converter : 20bit Delta-Sigma 128 times over sampling
Deemphasis : 50usec. / 15usec.
Copy Guard : Not Provided
Power Requirement : 120VAC, 60Hz
230V, 50/60Hz
240V, 50Hz
Power Consumption : 39W
Dimension : 482(W) x 150(H) x 371(D)mm
Weight : 9.0kg
- MECHANICAL
Motor Configuration : 2DD, 4 motors
Loading System : Front loading system
Fast Wind Speed : 180 times (maximum)
Fast Wind Time : Approx. 60sec. (T-120 Tape)
Search Speed : 1/2, 1, 2, 3, 5, 9, 16 times
- MEMORY REPRODUCING
RAM : 8Mbit, 5sec.
RAM Search Speed : 0 - 1time
- ELECTRICAL CHARACTERISTICS
R/P Frequency Response : 20Hz to 20kHz
S/N : 92dB
Dynamic Range : 92dB
T.H.D. : 0.05% (1kHz, +4dBu)
Channel Separation : 80dB (1kHz)
Wow & Flutter : Less than measurement limit
Standard Recording Level : -20dB / -18dB / -12dB (switchable)
(default:-12dB)
Meter Display : FL, 28 segments (level) 7 seg. X 14 lines
- AUDIO INPUT / OUTPUT CONNECTORS
ANALOG AUDIO INPUT
BALANCE
Connector : XLR-3-31 type (Pin2:Hot) x2
Reference Input Level : +4dBu
Input Impedance : More than 20k ohm
UNBALANCE
Connector : RCA Pin x2
Reference Input Level : -10dBV
Input Impedance : More than 10k ohm
ANALOG AUDIO OUTPUT
BALANCE
Connector : XLR-3-32 type (Pin2:Hot) x2
Reference Output Level : +4dBu
Load Impedance : More than 600 ohm
UNBALANCE
Connector : RCA Pin x2
Reference Output Level : -10dBV
Load Impedance : More than 10k ohm
DIGITAL AUDIO INPUT
AES/EBU
Connector : XLR-3-31 type
Format : IEC958 Part3 (AES/EBU)
S/P DIF
Connector : Optical
Format : IEC958 Part2 (S/P DIF)
DIGITAL AUDIO OUTPUT
AES/EBU
Connector : XLR-3-32 type
Format : IEC958 Part3 (AES/EBU)
S/P DIF
Connector : Optical
Format : IEC958 Part2 (S/P DIF)
HEADPHONE OUTPUT
Connector : 6mm dia stereo phone jack
Load Impedance : More than 8 ohm
Maximum Output : 100mW (at 32 ohm)
37PIN REMOTE
Connector : D-sub 37pin x1
Command Input : Parallel input
PNP transistor input
Low active (4.7k ohm / +5V, pull up)
Status Output : Parallel output
Open collector (4.7k ohm / +5V, pull up)
- GPI
INPUT
Connector : DIN 5pin type
Input : PNP transistor input
Low active (4.7k ohm / +5V, pull up)
OUTPUT
Connector : DIN 5pin type
Output : Open collector
VCEO:25V
Icmax:25mA
- MODEL 8335 TC/SYNC CARD SPECIFICATION
- TIMECODE INPUT
Format : SMPTE/EBU
BALANCE
Connector : XLR-3-31 type
Reference Input Level : 2Vp-p
Minimum Input Level : 0.25Vp-p
Input Impedance : More than 20k ohm
UNBALANCE
Connector : RCA Pin
Reference Input Level : 1Vp-p
Minimum Input Level : 0.25Vp-p
Input Impedance : More than 10k ohm
- TIMECODE OUTPUT
Format : SMPTE/EBU
BALANCE
Connector : XLR-3-32 type
Reference Output Level : 2Vp-p
Load Impedance : More than 600 ohm
UNBALANCE
Connector : RCA Pin
Reference Output Level : 1Vp-p
Load Impedance : More than 600 ohm
- VIDEO
INPUT
Connector : BNC
Format : Composite
Reference Input Level : 1Vp-p
Input Impedance : 75 ohm On/Off (switchable)
THRU
Connector : BNC
Reference Output : Direct output of VIDEO Input
- WORD
INPUT
Connector : BNC
Reference Input Level : TTL level
Input Impedance : 75 ohm On/Off (switchable)
OUTPUT
Connector : BNC
Reference Output Level : TTL level
Load Impedance : 75 ohm On/Off (switchable)
- MODEL 8336 RS422 Card SPECIFICATION
Connector : D-sub 9pin x1, comply to RS422 specification
Protocol : Comply to Sony 9pin protocol
Device Mode : Controlled fixed
|
|
 |
